In-Circuit Emulator Smart Kit Target boards Special Probe Adapters
	Program Download / Upload Program alteration function Real time Emulation support (action to CPU maximum speed) Inside Register indication and alteration function Single Step debugging function ROM Breakpoint debugging function RAM Breakpoint debugging function Interval Timer / Counter function (program run chronometry) Real - Time trace function Real-time RAM(Register) Indication function Run history function Sub-clock In action mode debugging function Target CPU ÀÇ Clock Frequency alteration function Target CPU   VDD Voltage alteration function OTP/MTP Program function IAR C-compiler Support

  It is Smart Kit increased SAM4 (S3C7xxx series) of Samsung, emulator for the exclusive use of SAM8 (S3C8/9xxx series) micom.
Composition of Smart kit relationship debugging system was composed by development micom's user baud, Target Board, Probe Adapter.
In compatibility been PC more than PC A 486 of Smart Kit increasing user action very design, and debugging environment was designed so that user may can use easily Tulba and function and I support user software including Samsung SAM4/SAM8 assembler.
Also, C-languange can develop application to system because user uses IAR SAM8 C-compiler to Smart Kit (SK-1000 Eemulator).

 Supported IC
  
   - SK-1000 : SAM4 (S3C7xxx) including SAM8RC Koa of Samsung/SAM8 (S3C8/9xxx) series MCU.

 Hardware characteristic

• Emulation Memory maximum capacitance
  SK-1000: 64K byte

• 16K (16 bits wide) Real-time trace memory

• RS232C interface because come PC.

• Target MCU relationship VDD voltage adjustment.
  - Because user controls VDD voltage to Smart Studio software, user can use.
  - Can control extent: 3.0 ~ 5.0 [V] 

• Real Time Emulation  ÃÖ´ë¼Óµµ·Î ó¸®
  - SAM4: 10MHz / 5.0V, SAM4 Series maximum wind velocity 6Mhz
  - SAM8: 25MHz / 5.0V, SAM8 Series maximum wind velocity  25Mhz
  

• Product standard : Width 165 (mm), length 215 (mm), height 45 (mm), weight 1.2 Kg

• Case of product comes as iron and aluminum..

Emulation Characteristic

• Program Download and Upload and memory edit function
• Run/Stop, Reset, Go to cursor, Go to address, Breakpoint run function
• Program SKIP function
  - Skip to cursor, Skip to address, Step over (subroutine calls)
  
• All register prices are emblematic and user can change.
• Single-step Practice
  (User by Single-step practice change value refer can.)
  - Executing once Single-step
  - Executing until suspend Single-step
  - Single-step run chart possibility by number of times until 255th
  
  
• Break point establishment in memory house number of program (ROM Breakpoint run)
  - Break point can reach to point branch office and establish as do radish that stop.
  - Number of times of break point can do 1 ~ 255 set.
  - Break point does continuation practice until suspend.
   
• Timer/Counter function
  - Can measure progress step of program by time.(Time between program interval)
  - Imperative withdrawal counter (program code size)
  - Imperative practice counter
   
• Real time trace feature (Real-time trace)
  - 16K I record stream of real time chase silver program in memory.
   
• Program run recording example function (Run history )
  - 16K Can always see if real time program run recording suspends after program run.
   
• OTP/MTP (Flash) Programming Function
  - Read, Program, Blank check, Verify, Read protection, and
    Checksum Confirmation function can use causing all OTP/MTP .
  - Erase, LDC protection, and Hard Lock Function is applied to MTP.
   
• All emulation functions do sub-clock (32768Hz lower speed) mode sequence chart possibility.
   
• Clock frequency control possibility of Target MCU
  - User can change Target MCU Clock frequency to Smart Studio software.
   
• RAM(Register) breakpoint run Function
  - Read, Write, Read/Write Condition
  - Various data format support (Decimal. Hexdecimal, Binary)
   
• RAM(Register) Indication function
  - Sampling Cycle : 100ms
  - Read / Write Read according to notation, Write possibility
   

  Software characteristic ( Smart Studio )

• It is Smart Studio increasing windows 95/98/2000/XT debugging software and it is integration development environment software that can compile because user edits direction source.
  User can use usefully that system is used in windows for sight anger of data.
  :Source window of multiplex :Tulba with each function :Vitality can compare menu for writing sieve of special function input as well as user in done window.
  :Windows window can utilize done working space maximum by minimum and maximum.

• User can make debugging environment store environment that is established or establish in Project.frm file.
  When recommence if store debugging environment, can work to debugging environment fast.
  This file stores variable RS232 set, device composition, object file, window arrangement, number of break point and time.

• Time, variable can establish usefully to learn Register result by imperative.
  Time, variable can edit in windows window for program analysis and directly.

• I support general assembler SASM of Samsung.